SRV® package basic equipment Oscillation and rotation
Couldn't load pickup availability
SRV® package basic equipment oscillation
and rotation:
For testing lubricants according to standards
as well as according to application-specific parameter sets
in oscillation and rotation mode with model
specimens
SRV®5 basic configuration Oscillation (x-axis) floor standing device
Test force range 25 - 2500 N
large recording block with two piezoelectric
force transducers
parallel rocker
OCA operating and control software with analysis package
1 (highlights: automated process start,
test start procedures, XY display,
Report generator, diagnostic options for PC
and SRV®, extensive read-out options,
Clear presentation of results, preparation for
TriboProfiling® data analysis)
Monitor table, 23 inch LCD touch monitor
High-quality industrial PC for large
Data throughput and 365-24/7 operation (7 years
Availability guarantee for spare parts, manufacturer
site guarantee), mouse, keyboard
Manual
Factory calibration certificate and declaration of conformity
calibration oil
rotary base module
rotary block, rotary engine
Radius shift (y-axis)
2-channel sensors for torque 40 Nm and
Friction 400N
Control and measurement software (RPM, left-right,
Measurement of friction torque, friction force)
Adapter for holding test discs
100x10mm
Software options for the OCA software
High Resolution Signal Analysis (HRA) Oscillation:
Friction signal analysis, shown for 1 period
Representation of friction hysteresis
High Resolution Signal Analysis (HRA) Rotation:
Spatial and time-resolved analysis of friction torque
and frictional force, shown on one each
rotation turn
Combi-Drive: Joint operation of at least
two out of three possible types of movement
(oscillation, rotation, y-axis)
Accessories for test preparation:
Insulated clamp screw for the upper
specimen holder
Interchangeable parts in the middle for test discs Ø 24 mm
Interchangeable parts off-centre for test disks Ø 24 mm
Tweezers to hold the specimens and spatula
to apply the lubricant
Fat gauge for the defined application of fat
the lower specimen
Tool set for test preparation
Specimen holder and adapter for oscillation:
Ball holder for 10 mm steel ball
Specimen holder ring/surface for ring or
Surface geometry 21 x 6 mm
Line holder for steel cylinder 6 x 8mm, longitudinal support,
10° angular offset
Specimen, material: 100Cr6, fully hardened:
50 pieces discs 24 x 7.9 mm, lapped on both sides,
according to DIN 51834, surface 0.50-0.65 µm Rz
100 pcs. steel ball 10 mm, polished, DIN 51834
10 discs 100 x 10 mm, lapped surface,
usable on both sides, Rz approx. 0.50-0.65 µm, flat
parallelism 2 µm
10 pcs. pin 3 x 15.8 mm, polished
Two-day operator training at our premises in
Munich
For on-site commissioning and training, ask
us for an offer.
and rotation:
For testing lubricants according to standards
as well as according to application-specific parameter sets
in oscillation and rotation mode with model
specimens
SRV®5 basic configuration Oscillation (x-axis) floor standing device
Test force range 25 - 2500 N
large recording block with two piezoelectric
force transducers
parallel rocker
OCA operating and control software with analysis package
1 (highlights: automated process start,
test start procedures, XY display,
Report generator, diagnostic options for PC
and SRV®, extensive read-out options,
Clear presentation of results, preparation for
TriboProfiling® data analysis)
Monitor table, 23 inch LCD touch monitor
High-quality industrial PC for large
Data throughput and 365-24/7 operation (7 years
Availability guarantee for spare parts, manufacturer
site guarantee), mouse, keyboard
Manual
Factory calibration certificate and declaration of conformity
calibration oil
rotary base module
rotary block, rotary engine
Radius shift (y-axis)
2-channel sensors for torque 40 Nm and
Friction 400N
Control and measurement software (RPM, left-right,
Measurement of friction torque, friction force)
Adapter for holding test discs
100x10mm
Software options for the OCA software
High Resolution Signal Analysis (HRA) Oscillation:
Friction signal analysis, shown for 1 period
Representation of friction hysteresis
High Resolution Signal Analysis (HRA) Rotation:
Spatial and time-resolved analysis of friction torque
and frictional force, shown on one each
rotation turn
Combi-Drive: Joint operation of at least
two out of three possible types of movement
(oscillation, rotation, y-axis)
Accessories for test preparation:
Insulated clamp screw for the upper
specimen holder
Interchangeable parts in the middle for test discs Ø 24 mm
Interchangeable parts off-centre for test disks Ø 24 mm
Tweezers to hold the specimens and spatula
to apply the lubricant
Fat gauge for the defined application of fat
the lower specimen
Tool set for test preparation
Specimen holder and adapter for oscillation:
Ball holder for 10 mm steel ball
Specimen holder ring/surface for ring or
Surface geometry 21 x 6 mm
Line holder for steel cylinder 6 x 8mm, longitudinal support,
10° angular offset
Specimen, material: 100Cr6, fully hardened:
50 pieces discs 24 x 7.9 mm, lapped on both sides,
according to DIN 51834, surface 0.50-0.65 µm Rz
100 pcs. steel ball 10 mm, polished, DIN 51834
10 discs 100 x 10 mm, lapped surface,
usable on both sides, Rz approx. 0.50-0.65 µm, flat
parallelism 2 µm
10 pcs. pin 3 x 15.8 mm, polished
Two-day operator training at our premises in
Munich
For on-site commissioning and training, ask
us for an offer.